Water Heater Repair Austin's Blog

Austin Homeowner advice and maintenance tips for water heaters.

Quick Reads of Important Water Heater Topics

Preventing Legionnaires’ Disease

Legionnaires’ disease. . . is easily picked up by breathing in contaminated water – such as mist from your shower, spray from a fountain or a hose, and even steam from hot tubs and cooking. The easiest things you can do to help keep your family safe is to ensure you maintain adequate levels of disinfectant in places where warm water sits (like hot tubs or fountains) and that you keep your water heater set at 140°F (60°C) or higher to ensure bacteria cannot grow in the tank or in the pipes as the hot water circulates.  http://theplumber.com/preventing-legionnaires-disease-in-your-home/

Shorten the distance hot water travels

Water is wasted down while you wait for the right temperature. One solution is a recirculating pump that moves hot water to the outlet while bringing cold water back to the heat source. In this scenario, water is not wasted, because hot water is automatically pumped to the fixture before the consumer turns on the water.  https://www.safeplumbing.org/what-you-can-do/be-water-efficient

Ways to Save on Water Heating Costs

There are four ways to cut your water heating bills: use less hot water, turn down the thermostat on your water heater, insulate your water heater, or buy a new, more efficient model.  http://energy.gov/energysaver/tips-water-heating

Learn more from ENERGY STAR on water heaters and check out their comparison chart of certified heaters.

Water Heater History

Much like a bunch of developments we utilize today, the beginnings of the contemporary water heater can not effortlessly be traced back to simply one person or society as its creator. It may not be as mysterious as some developments however it is absolutely an invention that we make use of on a daily basis. Having hot water in residences has actually assisted make our lives much easier and much healthier, and should not be something we forget about.

It makes us chuckle some when we see literature and see ads for tankless hot water heaters with the advertising message of “instant hot water.” Certainly, it would be fantastic to have, and of course it can save water that would go down the drain as one awaits the heated water to travel through ones house plumbing pipes from the hot water heater to the tap; yet are we that spoiled that we can not wait a number of seconds for the hot water to flow out? In this article we will be taking a look at a few of the societies and individuals that have actually assisted with the innovation of bringing hot water into the residence for us to enjoy this modern-day comfort.

I remember watching old Western movies when I was a kid and people would fill bathtubs with water heated up from a stove or fire. This was a time consuming process, but just what individuals did before having the innovation of a hot water heater. Over the past one hundred years or so, the good news is this procedure is not required any longer.

The Romans had their hot baths, which is typically considered to be an early form of water heating. They had an outstanding approach of heating their buildings with circulating air warmed from a fire below the flooring. Kind of like a very early kind of radiant floor heating. They utilized fires to heat water in big lead boilers attached over the heating systems. This was made use of for their huge bath houses which resembled saunas.

Currently we are going to leap ahead to the English painter, Benjamin Waddy Maughan. He had the very first patented for a hot water heater in 1868. In his design, natural gases heated up the water but there was not a flue to eliminate the gas vapors that are produced at the same time. This was the very first time that gas, not a solid fuel source was used in heating water. This innovation by Maughan had the cold water move through wires that were heated by the hot gases of a burner. The hot water created after that went into a sink or bathtub. It was called The Geyser, for the inventor had the concept from an actual water geyser.

Due to Maughan’s lack of air flow, his water heater was not used inside the residence. Today, if a water heater is not ducted effectively, carbon monoxide gas may go into the home, which is a huge issue.

Maughan’s development did go on to influence Edwin Ruud, a Norwegian mechanical engineer who was the creator of the automatic storage hot water heater in 1889. Throughout the 1880s in Pittsburgh, Rudd began the procedure of identifying the best ways to produce heated water safely. The business he started, Ruud Manufacturing Company, is still a leading developer of water heaters today. By the time of Rudd’s death, he managed to alter the day-to-day hygienic routines of the majority of every American.Rudd Water Heater Patent

The following is from Rudd’s patent:

In a patent obtained by me December 30, 1890, No. 443,797, I have described and claimed certain improvements in Water-heaters, such improvements consisting, generally stated, in certain mechanism controlled by the temperature of the Water in the boiler for regulating the flow of gas to the burner employed for heating the boiler.

The present invention has for its object a construction of the regulating Inechanism, whereby the flow of gas to the burner may be more nearly proportioned to the quantity of cold water admitted; and in general terms the invention consists in the construction and combination of mechanical devices or elements, all as more fully hereinafter described and claimed.

In the accompanying drawing, forming a part of this specification, is shown a sectional elevation of a water-heater having my improvement applied thereto.  (read more. . .)

In England around 1895, Ewart & Son developed a gas fired hot water heater called the Royal Geyser. It would be mounted beside a tub. It was gas fired and heated water that was going into the bath tub. The warm water was blended with cold water to develop the temperature one desired. The innovation was a little fragile, for if the water was shut off before the pilot light being turned off, it would normally wreck the heater.Ewart Royal Gyser Water Heater

The 1900s are considered the golden era of water heaters. There are many companies that began in the USA, supplying thoughts and technologies to constantly improve the overall design. We have electrical, gas, tankless as well as solar water heaters today, all of which have a fascinating history for their developments.

I mentioned tankless water heaters in the introduction of this . Though many individuals still consider them a current item in the plumbing field, however they were really very first created in 1929! Stiebel-Eltron produced the initial electric tankless heater, or coil immersion heater.

Other terms made use of to refer to water heaters that are still around today are an electric water boiler, electric dispensing pot, geyser, or electric water urn.

So there is a concise history of the modern water heater. Attempt to bear in mind that it is a home device that does require a little care every now and then too. With any luck our Austin water heater customers will have the ability to not take their water heater for granted more and will certainly make certain to comply with correct maintenance actions.

A Safe Water Heater

The water heater inside ones residence is normally not provided a bunch of normal upkeep. Fortunately for a lot of Austin house owners, it is a home device that can operate for several years without the requirement of much maintenance, even with it having among the most essential tasks in the house – providing warm water. Warm water is something that is used each day within a house, so the warm water heater certainly obtains a great deal of use!

However, if homeowners want to obtain as long of a life as feasible from their water heater, it is smart to provide it some focus once in a while. The average life span is around ten years. Some will last longer, however lots of will certainly last a whole lot less if one never ever does any kind of upkeep to it.

The main thing to be careful of is that a significant water leak from a water heater could create a great deal of destruction to ones residence. And, this is something that is not uncommon either. If residents do some very easy and fast routine maintenance, the majority of problems can be detected prior to they turn into significant repairs.

Among the simplest points to do is to regularly examine to see if any type of water is visible around the area that the hot water heater Austin Water Heater T&P Valvelies. This is not necessarily an indication that the unit will require changing, for it could be a small leak from the drain valve, situated below the water storage tank, or a leak from the T&P shutoff, which the picture to the right reveals just what that looks like. The temperature and pressure relief valve has a vital job of making sure the water tank does not blow up. Could that truly take place in your house? It could, however is not a routinely taking place also for residents. This valve, when running correctly, will certainly launch any additional stress that will naturally accumulate inside the water tank. Property owners could lift the shutoff and let go of it twice per year. If need to snap back right into placement once the shutoff is released. If it does not do this, it will most likely need changed. Try it a couple of more times to see if it does. A bit of water will usually appear from the valve and one will certainly listen to the sound of air being released. This is normal. If the valve has water that remains to leak from it, the valve will certainly need to be replaced. This is a task ideally left for a licensed Austin water heater repair company to take care of, however it is not a pricey repair.

Property owners will likewise intend to make sure that the flue pieces leading from the hot water heater outside are undamaged and sealed well. Otherwise, carbon monoxide can be released into the residence (where the water heater lies), which is really significant. This is the make factor, together with ones residence furnace, that a carbon monoxide detector be installed in homes.

It is additionally a great technique to drain a pail full of water from the hot water heater yearly to make sure there is not an excess of sediment establishing inside the water storage tank. It is likewise a great practice for it will certainly ensure the drain valve is functioning appropriately too. Let the complete bucket of water rest and settle. If it has a great deal of debris at the bottom, it would certainly be wise to drain the flush the water storage tank. We will not go into detail on how you can do that here, however again, we can assist with this task.

New Water Heater Technology

It is popular opinion, and the U.S. Department of Energy informs us this also, that heating water uses about 18 % of the regular home’s yearly power consumption. The only other house device that makes use of more is the HVAC system. With the typical tank hot water heater that most house owners make use of, it is keeping 40 to 50 gallons of water hot all day regardless of when it is being utilized. Typically with this situation, 20 to 50 percent of the energy being utilized is totally wasted. What are some alternatives to help curb this power loss? The company Aquanta, use to be called Sunnovations has been developing a feasible solution for several years now.

Sunnovations had a crowd-funding project in 2014 that did not reach its complete financing yet that is fine with the company for they were able to garner lots of interest from distribution companies that has become fruitful with a 2nd go around currently. Aquanta is presently taking pre-orders on a new smart water-heater controller, which they believe will certainly be delivering in July of this year.Aquanta Water Heater Controller

Aquanta’s CEO Matthew Carlson states that the company’s new technology has been field tested for a year now. It is surprising that other firms have actually not begun developing a similar device, specifically with the initial crowd-funding campaign … despite it not succeeding for them initially. Given that water heaters normally have a life of 8 to 12 years, it is not rational to replace it when it is running okay, but simply doesn’t have all the modern technology that a new hot water heater could come with. Several new water heater models are making use of smart technology functions, however there is nothing that will work with any model of current hot water heater to “make it smart.” Sears recently put out a hot water heater controller that does work on some of its models, yet not all of them and not with different companies hot water heaters.

The only various other device that is just a little similar is a hot water heater timer. However it works like a timer, turning the heater (and only electric hot water heater) on and off at certain times of the day; and not by means of smart technology.

One of the functions of the Aquanta technology is it will “learn” exactly what the water use patterns are inside the home. Most people have the tendency to shower, utilize the dish washer and various other hot water utilizing home appliances around the same time of day. The gadget will function to readjust the water heater’s temperature level to fulfill the need throughout peak times, and minimize the energy use during non-peak times.

The Aquanta will be situated in addition to a water heater. A probe is installed behind the T&P valve port and after that the probe is connected to the controller. A 2nd sensor is taped to the cold water supply. An optional 3rd probe is created to detect if there is a water leak from the heater as well.

Last but not least, the controller needs to be connected to a Wi-Fi network and house owners will install the smartphone application on a phone. The controller connects to Aquanta’s cloud-based server and begins its work of learning the home’s warm water use patterns. It is likewise possible to manually enter in the water usage pattern as well. So, it may manually and automatically control the heater’s power usage.

It is designed so a handy house owner can complete the installation him or her self. If a property owner doesn’t feel up to the task, a plumbing expert could definitely aid the firm specifies. Aquanta estimates it taking around 40 minutes for a house owner to complete the set up.

The device will work for the majority of water heaters, regardless of the fuel type. It depends upon the power source if it will function or not. There has to be an electronic ignition system, which most all more recent hot water heater will certainly have. Old gas heaters might not though. Definitely check out the compatibility information on the company’s website right here to find out.

Exactly how much energy, and then equated into money, can a home owner save with the device? Below is exactly what Aquanta claims on their website: “our data suggest that at least 20% and up to 50% of that energy in a typical home is wasted through ‘standby loss’. We are being careful to not overpromise, and have 3rd party testing underway to more specifically quantify the saving opportunity. However, our internal studies and modeling suggest that between 10-30% of water heating energy can be saved by intelligent control through Aquanta. The economic value of intelligent control of water heaters is much higher when factoring in peak or time-of-use pricing and utility peak demand reduction and similar incentives.” (read more here)

What others around the internet are saying:



Back to our blog. . .

How Healthy is My Water Heater

The hot water heater in ones Austin home ought to last a very long time without should have a lot of repairs executed on it. There are some easy upkeep actions homeowners must be doing to assist make certain it will last a truly long time without needing numerous, if any, repairs, which we have already discussed here.

There may come a day, though, when no, or not sufficient hot water flows out of a faucet like it once did. This article is will look at exactly what to do when the water heater is not producing hot water. There are numerous reasons why this could possibly take place, and several indications the hot water heater has actually due to the fact that house owners generally will miss out on. We will certainly not be judging homeowners for missing out on these indications. Nonetheless, there are some major indicators that will certainly take place eventually, to let one know exactly what either a significant repair is needed, or it is close to completion of the water heater’s life.

Exactly How Old is the Hot Water Heater
If the house one lives in was bought, it is simple to be unclear just how old the water heater is. Water heaters will continue to run for years, sometimes much longer than the variety of years it is developed to function. Because of this, it is easy to neglect the last time it was changed. So, if property owners offer it merely a little focus, one will certainly be surprised at the length of time the heater will certainly run well.

There is an identification number on the water heater that will state the year it was made. If the heater is greater than ten years old and requires some significant repairs, changing it needs to absolutely be taken into consideration.

Is There Discolored Water Originating from the Hot Water Heater
Anytime the water from hot water taps in the house has a discolored or rusty shade, it usually means there is rust inside the hot water heater tank. This is not a good things to see. When the interior of the storage tank begins to establish corrosion, it is an eventual truth that the storage tank will certainly rust through completely. The important point to watch for is water leaking from the tank, for it will eventually create a huge mess if the water heater is not changed prior to the container rusting through.Austin Water Heater Repairs

Nonetheless, there can be various other reasons that the water is discolored. We do not have space in this post to review them, but give us a call to review what could be happening.

The Water Heater is Making Strange Sounds
Through the organic course of a water heater operating, sediment will certainly form on the inside of the tank. As it is heated, and reheated, the sediment will solidify, and can bring about lower performance. It will take much more energy to heat water after that. The more sediment that forms will start to trigger banging or popping noises from within the tank. They could get extremely loud as well. It is not as large of an issue as it might seem to be. The sediment can be eliminated with flushing the storage tank. We would like to do this process for you, however house owners are able to conduct it themselves. For safety and security reasons however, we would absolutely like to help.

There is Moisture Around the Warm Water Heater
Anytime dampness starts to collect around the hot water heater it might show that there is a small leak or crack in the storage tank. When metal heats, it expands and can form slight fractures. The older the heater is, the easier this could take place. Nevertheless, do not panic if you see dripping water, for it can likewise be coming from a plumbing connection or fitting that is lose. Maybe originating from the temperature and pressure relief valve also. Dripping water seem like a bad sign, but it could possibly additionally be a very easy fix or connection tightening up.

If any of these things are happening, call us to schedule concerning see what the required Austin water heater repair should be. It is well to allow us handle and servicing done to the system to make sure the guarantee is not nullified by any type of maintenance carried out by an unlicensed individual.

Austin water heater repair signs

Quick Water Heater Maintenance Tactics

Let’s talk about doing some water heater maintenance today? It will not take too long. . .truly we were planning on ten minutes. Yes, that could be all it will take to complete 2 maintenance tasks that every property owner can perform. The best aspect is they can help Austin TX property owners with the following:Austin Water Heater Maintenance Steps

Making certain ones water heater survives for a long time, conserving expenses.
Making certain ones water heater works safely.
Ensuring that it operates as energy efficiently as possible, also conserving money.

So with that in mind, let us educate you on how to invest 10 minutes once or two times a year to help prevent any water heater repairs for your Austin water heater.

Examining the T&P Relief Valve

The job of the temperature and pressure relief valve, otherwise known as the T&P Valve, is incredibly significant. It has the necessary job of making certain too much pressure does not build up inside the storage tank, which in turn makes certain the water heater won’t explode. The infographic following demonstrates the following ways in testing it. The lever should be lifted a little then release it. Ideally, it snapps back to its original position immediately. When it’s working appropriately, a bit of water may be heard going in the drain pipe below the valve handle that was previously raised and the sound of some pressure released is possibly noticed. One will require a new valve whenever none of these items occur during the evaluation.

Undertaking a Mimi Water Heater Tank Flush

Naturally, rust and corrosion will appear inside the water tank because of the chemical reactions happening with the elements that are necessary to heat the water. We are not going to go straight into the complicated chemical specifics here, but simply by flushing a little of the water, it helps get rid of the sediment, and supply a chance to find out just how much sediment is within the water heater.

To complete a tiny flush, place a pail underneath the drain valve, positioned at the bottom of the tank, and open the drain valve. Only drain several gallons of water – a couple containers full. Permit the water to sit in the last pail for a number of minutes. After it settles, examine to determine how much stuff has settled to the lower part of the bucket. If there is, if the water heater has actually not been drained for a long time (or ever), it would be best to do a complete flush of the tank to get as much of the sediment out as possible.

Examine how clean the water looks. When it doesn’t seem too unclean just conducting the mini flush will probably be fine. If there is a great deal of gunk in the water a whole flush should really be executed. If you already know it hasn’t been drained for a long time, if ever, it is advisable to drain all of it.

We can not go directly into all the measures in this article to accomplish this, although for educational purposes, first turn down the temperature. Wait at the very least 1 hour to enable the water to cool down prior to draining it. Rather than making use of the buckets, it really is much simpler to attach a hose to the drain valve and drain the water outdoors.

If one starts to listen to strange cracking sounds from the water storage tank, it is a signal that there may be a substantial level of sediment accumulating inside. This reduces the energy efficiency of the water heater.

Water heaters will function rather effectively without a lot of maintenance, and quite a few people usually do not execute any maintenance to them. Nevertheless, to gain the 3 advantages listed at the beginning of the post, it is crucial to at least perform these 2 responsibilities. If you have any queries or feel like you want some help the very first time, contact us! We are always accessible to aid and to help reduce an unwanted Austin Water Heater Repair.

Check out more tips to increase the heater’s energy efficiency here too.

Water Heater Repair Austin Texas

From Visually.

Removing Water Heater Smell

Whenever the water coming out of the taps inside the house smells bad, there is probably an issue with your water heater. There are multiple different reasons for smelly water, however the primary reason is bacteria. In case bacteria is getting into the water, an odor will likely come about. Well water is usually responsible for this taking place. Even so, there are some steps an Austin homeowner may take to prevent bacteria from growing in their water and to remove current bacteria and odors.

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more here…

Reducing Water Heater Bacteria Growth

The most effective way to prevent bacteria from growing and bringing about unpleasant tastes and odors in one’s house, is to make sure the temp is fixed at 140 degrees or higher on one’s hot water heater. At this temp bacteria cannot grow and will die. Whenever your water heater temperature is placed below this, bacteria will not only exist but may multiply.

Eliminating Water Heater Bacteria GrowthAustin Water Heater Odorsv

To remove present bacteria and smells, one must use chemicals to kill it. Chlorine bleach is the most efficient and comprehensive chemical cleaner to utilize. If perhaps you are trying to clean the water and remove the bacteria using bleach by yourself, be sure to understand the precise way of doing this. First of all, the electric or gas going to the hot water heater has to be switched off. Next the cold water supply will have to be turned off. After that, you will have to switch on one of the hot water faucets inside of the home. This lets air into the tank. Working with a garden hose, empty the water out of the water heater and shut the drain valve after all of the water has been drained. After this, it’s time to pour in the bleach. One will need five oz of chlorine bleach for each gallon of water the tank can hold. Detach the flexible cold water hose and pour the bleach in the opening. In case the cold water hose is not flexible, it could be a good idea to get in touch with a pro. Connect the water line once again and fill up the tank with water. It is crucial to turn off the hot water tap in the home when all of the air is out of the pipe. It’s also really important to run each one of the taps that use hot water inside the property until you are able to smell the bleach. The bacteria that is inside the water heater can also be in water lines and taps which means that you will need to eliminate the bacteria in these areas in the process. Let the bleach water remain in the tank and in the piping for nearly 3 hours not having using any hot water. Then an additional flush is in order. Once the tank is cleared for a second time, don’t put in additional bleach but fill it back up with water and allow it to remain inside the tank and inside the piping for a minimum of thirty minutes. Lastly, drain out the water just as before and refill the tank with water. Let all the hot water fixtures in the house drain until you can no longer smell bleach. Either switch the power back on or light the pilot light back up and you will be all set!

For any inquiries about water smells, flushing a hot water heater, Austin water heater repairs, or other water heater issues, call us!

4 Signs of a Water Heater Failure

Hot water heaters generally accomplish exactly what they are intended to and generally go undetected until one needs an Austin Water Heater Repair. However, several of the problems that come up can be avoided through regular servicing by a specialist. Make sure to monitor your gas burning water heater, because a number of the issues that can develop might be expensive and harmful for family members and animals. In this post, we’re outlining 4 signs that a gas water heater may possibly have to be swapped out.

Dripping Water

In the event that there is water on the ground near your hot water heater or dripping from a pipe, you might have to exchange the water heater. However, dependant upon just where the water is found and how much there is, you might be all right. In the event the hot water heater is dripping water out of a pipe and there exists a little bit of water on the ground next to the heater, it’s probably the T&P valve. The temperature and pressure valve eliminates unnecessary water vapor from the hot water heater, this kind of steam becomes to water and will come outside of the water heater by way of a pipe to the side of the tank. If this is the case, it is actually completely typical and essential for the heater to work properly. Don’t try to move the T&P valve and never obstruct it. In cases where you may be worried about the amount of water that may be coming from the pipe, call an expert! If perhaps the dripping water is coming from the bottom of the tank, it is pretty much undoubtedly time to buy a brand new hot water heater. When the water heater heats water the steel tank expands and contracts, this movement could cause cracks and minor fractures, which will ultimately bring about leaks. Once this transpires, it will be time to buy a brand new system.Water Heater Repair in Austin TX


Around the pipes coming from the water heater you will find pipe fittings that need to be sealed tight to keep the pipe in place and keep water from dripping out of the opening. If perhaps you are finding corrosion around such pipe fittings, water is leaking out of the opening. While this is not a large leak and will not lead to immediate problems to the heater, in cases where the issue is not resolved, severe and costly complications can at some point develop.

Burn Marks

In cases where you happen to be seeing burn marks on the lower part of the water heater, there can be two possible problems. However, each of them happen to be very serious and both necessitate a pro. One issue could be with the venting. In the event the venting is clogged or was initially fitted incorrectly, it might cause the exhaust gases to come back in the house. This is dangerous and may cause health issues or fire when left alone for too long. But, this might not mean you have to replace the hot water heater, which is good. Another likely problem with burn marks might be the flue pipes inside the water heater are obstructed. This can result in a lot of harmful issues and, regrettably, the water heater will have to be replaced asap.

Yellowish Flame Color

Gas hot water heaters have a blue flame below the tank when it is running. But, if you happen to be seeing that flame is an orange or yellow shade, instead of blue, the burner isn’t operating properly and will have to be examined by a pro.

There are numerous issues that can come up with gas water heaters, however by using consistent care and yearly examinations, you may be able to avoid the need for an unexpected water heater repair in Austin that could potentially be costly. Give us a call today in case you see anything unusual with your hot water heater!

Complete Water Heater Maintenance Tips

Certainly there are a lot of unlucky experiences that property owners have concerning water heater routine maintenance of “getting out of bed to the chilly bath.” Well, we are not about to focus on how miserable of a predicament that is. In addition, we will presume that one knows the straightforward idea of making sure ones water heater is serviced routinely to receive the most out of its life time, and to make sure an emergency Water Heater Repair in Austin is not needed. This can help one save money on utility bills too. All that is practical we realize. While not needed a lot of maintenance, hot water heaters should have some. We are astounded, even though not shocked, by how many clients we see who have never executed virtually any servicing to their water heater), following are the tasks people must keep in mind with regard to routine maintenance.

The Potential Period of time an Austin Water Heater Should LastHot Water Heater Repair in Austin TX

8 to 10 years is the common duration a conventional gas water heater can last. There are plenty of factors which will have an effect on the general lifetime of course, however this is an effective standard. Probably the biggest element that will impact the long life of it is actually mineral deposits. The steps discussed in this article are supplied in hopes of assisting to minimize the buildup of mineral deposits inside of the water storage tank of the water heater.

Methods to Reduce an Austin Water Heater Repair

Homeowners, even people that usually do not feel overly handy, can achieve lots of water heater routine maintenance themselves. Even though more often than not, a water heater will run safe, try to remember that they actually do run off of electric power and/or gas. And so suitable safety guidelines ought to be used by Austin property owners. Remember to make use of these measures as an informative guide, for we would much rather demonstrate these together with you in person.

First, the water heater’s electric power requires to be turned off previous to accomplishing any maintenance. Ones breaker box should have a switch labeled that specifies which breaker is the heater’s. House owners that have a gas water heater, rotate the gas cutoff counterclockwise in order to shut off the gas.

Anode rods, or also referred to as sacrificial anode rods, are the portion of the heater that assists with reducing rusting inside of the water tank. A good number of are constructed from aluminum while some are made out of magnesium around a steel wire. In time the outside covering of the rods will erode and they ought to be changed at the time the steel wire is observable. They ordinarily last about 5 years, though that is reduced if ones water is soft. Ultimately, it is easier and less expensive to have the anode rods changed, to be able to obtain a long life out of the water heater storage tank. The rods ought to be reviewed on a yearly basis.

Take a look at the following video which illustrates the process of replacing the anode rods:

Our next water heater part we will look at will be the dip tubes. Not every water heaters have got them however. They must be checked every 6 months for deterioration. To check it, take it out and evaluate its length to the height of the water heater. It needs to be about 6″ to 8″ shorter compared to the storage tank. It’ll need to be replaced when it’s shorter than that, as well as displays symptoms of breakage or falling apart.

Forms of water heater flushes. Once more, mineral deposits are the primary cause of water heater breakdowns. Just how fast sediment establishes inside of the storage tank is dependent upon the quality of ones water. With time, this sediment can solidify, inducing popping sounds from the storage tank, reduce the efficiency of the unit, and possibly block the drain valve. Ideally, every six months, but a minimum of yearly, empty 1 or 2 gallons of water from the drain valve at the bottom of the hot water heater in a container or through a garden hose into a bucket outdoors. Look to observe just how much sediment is within the container once the water settles. If it seems to be fairly clear, that is good! When these types of small flushes are undertaken two times a year, one may not need to carry out a big flush as often. If the water looks really dirty, a full flush ought to be accomplished. It is likewise a very good time to guarantee the bottom drain valve of the storage tank is operating good and not leaking. These are commonly composed of plastic and as time passes if they aren’t opened up, they are going to get stuck or not close up tightly, which explains why it really is a good idea to open and close them during the small flush test.

The flushing process may help with getting rid of hot water smells that can occur too.

The reasons behind flushing a water heater are outlined in the next video:

For those that possesses vacation homes or temporary homes, one should drain the storage tank of all its water to help prevent any flooding throughout the times the property is not lived in. Of course, make sure to fill it up while the household is to be resided in again.

Inspecting water pipes. Analyze to make sure all water pipes have no leaks or are impaired in any way. It ought to be simple to see when there are any leaks with any piece of the water pipes or storage tank for it will have water beneath and/or near the unit. Leaking water may cause water damage to parts of ones property, so be sure all appears dry, primarily if the heater is within the residence and not in a garage.

T&P valve check up. Annually, the T&P valve, or temperature and pressure relief valve, needs to be examined. The T&P valve’s purpose would be to safeguard the water heater storage tank from excess pressure, and blowing up. The owners guide needs to be looked at to verify the appropriate methods are followed but listed here are the basic steps. A little water may come out of the valve and it will be really hot so be mindful. Raise the handle and let go of it. Have a bucket available to catch any excess water which can come out. Additionally, the noise of pressure getting discharged will be noticed. The lever will need to snap back in position. If perhaps it doesn’t give it a try once again. In case after a few tries it will not go back again into position, a new valve is going to be needed. The valve could drip a little water after doing that for a short period of time. If it doesn’t stop dripping after a couple of hours contact us.

Through the years, a lot of discussion has occurred on what exactly the best temperature needs to be for ones water heater. Makers usually preset heaters to 140 degrees, which is really warmer than almost all people will ever need. 120 degrees is the typical temperature and some individuals even go as far as 100 degrees. We are writing more about this, but we would suggest having the temperature around 120 degrees.

Guidelines For Gas Water Heaters

Every 3 months is a good time to check the gas venting system. All the fittings ought to be checked out to guarantee they’re tight, look for blockage, and look for damage to the vent pipes, and also ensuring they are absolutely free of rust and corrosion. Gasses are vented to the outside of the household with gas fired heaters. If these gasses make their way in the property it can be deadly and a fire risk. Make sure that everything flammable or corrosive is clear of the exhaust venting to aid the prevention of fires. Any loose, broken, or corroded sections of vent piping will be required to be changed.

Check out the pilot light to execute a visual diagnosis of the way it is working. The task of the pilot light is to light the gas burner that heats water for the household. To get a water heater to run at top performance, it is very important for the pilot light to be thoroughly clean. The flame color should really be blue with natural gas heaters. As for propane heaters, the flame should be blue/green with just a small amount of yellow at the tip. A short flame, a yellow flame, or a flame that has a split flame at the top indicates that an adjustment is required.

Steps For Electric Water Heaters

Making use of insulation wraps or blankets around the storage tank will help keep a consistent temperature inside of the storage tank without using as much electric power. Also, by the heater not having to perform as frequently will stretch the life of the heating element due to the fact it will not be utilized as much. Regularly, verify the insulation blanket to verify it is attached and hasn’t slipped or moved upon the water storage tank.

Routine evaluation of the heating element is significant and will help lessen the need for an emergency repair. We aren’t going to get into the specifics for a total examination here, however one will require a voltage/OHM meter to be sure there does exist a closed electrical circuit. Heating elements will need changing at times.

The area around ones water heater requires to be thoroughly clean of dirt. Specifically if the water heater is found in the garage, make certain to give the place a sweeping frequently. Ones heater will perform considerably better and be not as likely to call for an Austin Hot Water Heater Repair if it stays clean.

Replace Old Water Heaters With Energy Efficient Ones

Today, almost all water heaters made have a very nice volume of energy efficiency. As of April 2015, stronger efficiency codes were set up in the United States on water heaters. Clearly, the better quality the heater, the longer the life one will get out of the unit with the suitable maintenance over the years. Don’t hesitate to call Water Heater Repair Austin to talk about water heater maintenance or to answer any queries on selecting the most proper replacement water heater for ones household or office. Brand, model, and size need to all be considered in the course of the selection process and not just use the “bigger the better” saying. Regarding storage tank water heaters, it is a waste of energy to have a whole lot of extra water remaining constantly heated up to a hot temperature if not going to be made use of.

Minimize Water Heater Energy Usage

Water heaters are an out of sight, out of mind appliance. Luckily they are typically created to be so. Even with hot water heaters at this time available being well built with energy efficiency in mind, there are items house owners are capable of doing to stretch ones water heating energy bill even more.

Where to Save on Ones Austin Water Heating Costs

Take a look at the Thermostat Temperature SettingAustin Water Heating Cost Savings

If you haven’t seen the temperature level the hot water heater is established at, now could be a great time to do so. The factory setting is ordinarily approximately 140 degrees. Most house owners don’t need it to be set that high in the event that there are some health considerations one has. There is additional information on water heater temperature options here. Even changing down the temperature by 10°F can reduce energy costs by about $6 per month. The common house owner does not need to set the water heater higher than 120°, so think about turning yours lower in case it is.

Decrease Hot Water Usage

Here are some thoughts on how to lessen the hot water usage at home while not having a lot of impact on how one lives.
Clean the bulk of clothes in the washing machine in cold water: Most laundry detergents are developed for cold water use currently therefore take advantage of them.
Take showers in place of baths. Normally, baths take 12-15 gallons of water, while showers typically only make use of 5-9 gallons.
If renovating or changing sink faucets, add dual handle faucets. Single handle faucet will use some hot water when it is not needed. Regardless of whether the handle is moved straight up results in hot water to be used. Single handle faucets can help get rid of the use of hot water any time it is unnecessary.

Fix any water drips and leaks. We will not get into details here, nevertheless, even a small drip can calculate into a significant volume of water over the course of a month! Be sure to get any faucet drip mended as quickly as possible.

Adding Insulation to the Water Heater

It is smart to insulate the water heater and the hot water pipes. Insulated covers can be found to cover the storage tank to keep the stored heated water hot. Todays water heaters are manufactured with exceptional built-in insulation of the water storage tank, but every tiny bit can certainly help, particularly if the water heater is placed within a non-heated part of the house, such as a garage. All hot water pipes leaving the water heater should be wrapped in pipe insulation as well. It is especially important for pipes that run through a garage, crawl space, or other area not warm.

Flush the Water Heater Regularly

Property owners need to ensure they’re executing a little regular upkeep on the water heater to make sure it functions as effortlessly as possible. This will save on energy usage and prolong the life of the hot water heater. Through flushing the storage tank and checking the anode rod goes a long way in executing this.

Install a More Efficient Water Heater

Whenever it is time to get a new water heater, get one that is as energy efficient as you are able to invest in. In the long run it will definitely pay off!

If you have got any questions with an Austin water heater repair or perhaps if you are not certain whether it is getting close to needing a new water heater, do not wait to contact us.

How to Turn Off a Water Heater Fast

There can be instances when Austin homeowners will need to turn off their hot water heater fast, and it is necessary that ones knows the right steps in doing so.

Emergency Austin Water Heater Shut Off Steps

1. First shut off the Electricity or Gas

Gas – The thermostat dial must be turned from the “on” to the “off” position. This will turn off the gas at the water heater. If the odor of gas is ever recognized, get out of the home and call the local gas company without delay.

Electric – Locate the breaker box location and shut off the breaker for the water heater. One could possibly have a disconnect switch close to the water heater. Make use of this to shut off the switch to turn off power to the water heater.

2. Switch Off the Water Supply

Discover the cold water pipe attached to the water heater and follow it back to the origin or the wall. If it is an old design turn faucet handle, turn the handle clockwise up until it stops. This should shut off the water.

If you have a newer lever design ball valve pull or push the handle a one fourth turn. This should shut off the water.

3. Open the Pressure Relief ValveAustin Water Heater Repairs

This is also quite often identified as the T&P valve. Opening this will relieve the pressure in the water storage tank. A little water can come out of this whenever it is opened up that could be hot so be careful! Lift up the lever so it is sticking straight out or up.

4. Drain the Water Heater

It could be needed for the water heater to be drained of its water (this is optional). First, a garden hose has to be connected to the drain valve located towards the bottom of the water heater. Run the hose outside. Remember that the water being released of the hot water heater could have rust in it that could lead to injury to turf and plants, and will be hot. Inside the household, let flow the hot side faucet in the sink closest to the water heater. It will discharge the vacuum seal and let the water drain out of the water heater easier. It should take anywhere from 10-30 minutes for the water heater to empty.

These are vital plumbing emergency steps that hopefully you will keep in mind if having to deal with an Austin water heater emergency repair.

Austin Water Heater Repair Company Video

We love taking care of Water Heater Heater Repair in Austin TX and have enjoyed serving all of our neighbors. Return here in our blog for we will continue to provide tips on water heater maintenance and common care.

We would like to share our brand new company introduction video with you below.

We are likewise accessible to help you with every other kind of plumbing repair you might require carried out. Whether a leaking faucet, drain cleaning, toilet repair, or leak detection. We have seen practically any kind of emergency plumbing and water heater repair predicament you can picture and look forward to using our well crafted troubleshooting knowledge!

If it happens to be near to the time frame for a water heater replacement contact us so we can assist with looking for the best possible style of water heater for your home or workplace.

W. Samsel Master License #M5587
B. Samsel Master License #M18756